Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterECO Window Systems Custom & Geometric Windows in Oakland Park: What to Know First
We repair and replace ECO Window Systems custom and geometric windows in Oakland Park as an independent service provider, not as a factory-authorized dealer. Most custom ECO jobs in Oakland Park run a two-week turnaround from measure to install, with geometric shapes like arches, radius tops, and angled peaks taking a few days longer because of glazing lead times. Honest price posture: a custom ECO geometric window typically runs 15-30% above a standard rectangular unit of the same glass package, and we quote line-item so you see where every dollar goes. Call (863) 264-3649 for a free estimate.
This page is for Oakland Park homeowners who already own ECO Window Systems products and need a shaped window replaced or matched. It covers the failure modes we see most often, what the work costs, and how we approach a custom ECO job differently than a standard window swap.
Key Takeaways
- We service ECO Window Systems custom and geometric windows in Oakland Park as an independent provider, which means we make warranty-safe decisions without pressure from a manufacturer.
- Most geometric ECO failures trace back to seal stress or frame racking, not glass defects.
- Cost depends on shape complexity, glass package, and whether the frame is salvageable. We quote it all on paper before work starts.
- Every job carries the Done Right Promise and The Keystone Standard: both warranty layers registered in writing, durations stated, before the truck leaves the driveway.
How ECO Window Systems Products Fail - and How We Fix Them
Not every window fails the same way. ECO products have their own patterns, and we’ve learned them over years of working in Oakland Park’s salt air and hurricane-season humidity. Here are the five failures we see most on custom and geometric ECO units:
- Seal failure at the radius transition on arched tops. ECO’s radius and arch units use a bent-glass or segmented approach depending on profile. In Oakland Park’s humid summers, condensation creeps into the bend point where the glazing meets the frame. Owners mistake it for a leak. It’s usually a desiccant saturation issue inside the IGU at the curve. We reglaze with a matched-shape unit and a fresh edge seal, not a caulk patch.
- Frame racking on oversized trapezoids and rake windows. Large geometric shapes carry more glass weight per square inch of frame, and ECO’s aluminum extrusions on certain custom lines flex slightly over twenty-plus years of sun load. The symptom is a window that binds halfway up travel or stops sealing at the top corner. We reset the opening, shim to true, and re-square the unit before anchoring it back in.
- Hinge fatigue on casement-style geometric units. ECO casement and awning windows with non-rectangular sashes put uneven load on the hinge hardware. The lower hinge on a tall pentagon wears first because it carries the most shear. We replace the hinge set with rated hardware and adjust the sash so the reveal is even all the way around. That evenness is the difference between a window that closes for five seasons and one that binds again in two.
- Improper exterior flashing on site-built geometric openings. Many Oakland Park homes built in the 1970s and 1980s have original rough openings that were never truly square. When an ECO geometric unit gets forced into an out-of-square opening, the corners take stress they were never designed for. The tell is a diagonal crack in the frame corner or sealant that keeps pulling away no matter how many times the homeowner recauls it. We pull the unit, true the opening with new bucking, and reset it square.
- Glass stress cracks in oversized shapes after storm pressure cycling. Oversized geometric IGUs take pressure differently than rectangles during tropical storms. The stress concentrates at the shortest radius of the shape. ECO’s laminated glass packages handle it well, but if the original install left a pinch point between the frame and the lite, cracks start at the edge and run inward. We inspect before recommending replacement. Sometimes the unit is fine and the mounting was wrong. Dale Kessler’s rule on this: if it is not sealed right, it is not done.
Our ECO Window Systems Custom & Geometric Windows Process
Here’s how a typical ECO custom window job goes with us, from the first call to the cleanup:
- 1
Call and describe the window. A live person answers at (863) 264-3649. Tell us the shape, rough size, and what it’s doing. We’ll ask about the frame condition and whether it’s a repair or a full replacement.
- 2
On-site measure and diagnosis. We measure the rough opening and the existing unit, if one is in place, plus the sightline and jamb depth. We never measure once. Every opening gets measured twice, the way Dale was taught to do it as a glazier’s helper in Broward County.
- 3
Parts and glazing decision. If we can match OEM ECO glazing and hardware cleanly without voiding any remaining warranty, that’s the first choice. When ECO parts are discontinued or the unit is out of warranty, we source quality aftermarket glazing cut to the exact shape and build the IGU to spec. We explain the tradeoff on paper before anything is ordered.
- 4
The repair or replacement. We set the unit, shim it true, anchor it, and flash it the way the original install should have been done. Geometric units get extra attention at the corners and the shortest radius.
- 5
Test and document. We cycle the window, check the seals, verify drainage, and confirm the reveal is even all around. Both warranty layers get registered in writing before we leave the driveway.
- 6
Cleanup and walkthrough. We leave the opening clean and take you through what was done and what to watch for. If anything’s not right within 90 days, we come back and make it right. No paperwork fight, no fine print.
What ECO Window Systems Custom & Geometric Windows Costs in Oakland Park
Pricing depends on shape complexity, the glass package, and whether the existing frame can be reused. Here are the ranges we commonly see in Oakland Park for ECO work:
- Arched or radius top IGU replacement: $850-$1,400 per unit, depending on radius and glass package.
- Trapezoid, pentagon, or rake window full replacement: $1,100-$2,200 per unit for standard double-glazed, more for impact glazing.
- Oversized geometric window (6+ feet on the long axis): $2,200-$4,500 per unit with reinforced frame anchors and structural shimming.
- Repair-only work (hinge replacement, seal repair, frame resquare): $250-$600 per window on most custom shapes.
- Impact-rated custom geometric units: Add 30-50% to the base ranges above, depending on profile and lamination.
What moves the price: whether the shape requires a template (a physical pattern of the opening, sent to the glazier), whether the existing frame is sound, and whether we’re matching a discontinued ECO profile. We write fixed, line-item quotes with no change orders. Call (863) 264-3649 for an exact number. The estimate is free.
Why Oakland Park Homeowners Call TruePane Windows & Doors for ECO Work
We’ve been installing and repairing windows in Oakland Park since 2008 through our company’s heritage of craft and community commitment. Dale Kessler grew up off Prospect Road in Oakland Park and learned the trade at McFatter Technical College before working as a glazier’s helper and lead installer across Broward County. That local tenure matters on ECO jobs because we know which neighborhoods still have the original rough openings, which retrofit profiles were used in the 1980s and 1990s, and how the coastal air works on aluminum frames over time. We also service PGT, CGI, CWS, and ES Windows, so when an ECO unit isn’t worth saving, we can quote you a side-by-side replacement from another manufacturer line on paper. Every job is backed by the Done Right Promise and The Keystone Standard. Background-checked, uniformed technicians do the work. A live person answers the phone 24/7. We’ll be there when we say.
FAQs
It depends on the work and who does it. If there is an active ECO warranty on the unit, we work within its terms and use OEM or approved parts where they’re available, and we document everything. As an independent ECO Window Systems service provider, we’re not bound by a manufacturer’s parts pipeline, but we won’t do anything that quietly voids your coverage without telling you first. Call (863) 264-3649 and we’ll walk you through what your warranty actually covers before any work is quoted.
Yes. Most geometric shapes can be templated and cut new, even if ECO no longer lists the profile. We take a physical pattern of the opening and work with glaziers who cut to the exact curve or angle. The frame profile may be the limiting factor on very old or uncommon extrusions, but we’ll tell you honestly if the shape is matchable before you commit to anything. Call (863) 264-3649 and we’ll take a look.
Simple IGU replacements on common shapes usually close within two weeks from measure. Custom templated shapes and impact packages run three to four weeks, mostly because of glazing lead times. The on-site work itself is typically a single day for one or two windows. We’ll give you a written timeline at the estimate, and it holds.
If the frame is square and the rails are sound, repair usually makes more sense. If the frame is racked, the corner is cracked, or the profile is corroded enough that re-anchoring won’t hold, replacement is the honest answer. We’ll show you the condition on site and quote both options on paper when that’s useful. Call (863) 264-3649 to schedule an inspection.
When the job requires a permit under Oakland Park building code, we handle it. That includes most structural opening work and any impact-rated installation. We pull the permit, schedule the inspection, and don’t consider the job done until it passes.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Oakland Park and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.