Sliding & Patio Doors in Coral Springs - Free In-Home Measure, Written Price

Fast, Reliable Sliding & Patio Doors Across Coral Springs

Door Installation in Coral Springs for sliding door replacement typically runs $1,800 to $4,500 for a standard 6-foot impact-rated unit, and $4,000 to $9,000 for larger 8- to 12-foot sliders with multi-panel configurations. Most jobs we complete in a single visit once the unit arrives from the manufacturer, though the non-standard rough openings in older Coral Springs CBS homes mean custom sizing is the norm, not the exception. If your original aluminum slider is binding, corroded, or fogged between the panes, call (863) 264-3649 and we’ll send a technician who knows exactly what these 1970s and 1980s Coral Ridge Properties homes look like behind the stucco.

Call (863) 264-3649

Why TruePane Windows & Doors Is Coral Springs’s Preferred Sliding & Patio Doors Company

Custom Windows & Doors in Coral Springs is what TruePane has been providing long enough to know the difference between the homes along Wiles Road, the loops off Ramblewood Drive, and the gated sections near Eagle Trace. The houses may look similar from the street, but the rough openings behind the stucco tell a different story. We’re led by Dale Kessler, a second-generation glazier who built this company on a rule that still governs every install: if the pane is not true, the job is not done. That standard applies whether we’re replacing a single patio slider or reframing a 12-foot opening for panoramic glass.

Our Sliding & Patio Doors team handles everything from straightforward replacements to full rough-opening rebuilds. Coral Springs homeowners call us because we quote manufacturer lines side by side on paper, register both warranty layers in writing before the truck leaves the driveway, and stand behind every job with our Done Right Promise. A live person answers the phone 24/7. Not a voicemail tree, not a callback form.

Our Sliding & Patio Doors Services in Coral Springs

Patio Sliding Doors

Most Coral Springs homes built by Coral Ridge Properties between the mid-1970s and early 1990s came with large aluminum-framed sliders opening to screened lanais. After 35 to 50 years in South Florida humidity, the bottom tracks corrode and the rollers fail or the frame binds. We replace these with impact-rated, fusion-welded units sized to the existing CBS rough opening, which almost always requires a custom or modified frame rather than an off-the-shelf size. A typical patio slider replacement in Coral Springs runs $1,800 to $3,800 depending on width, glass package, and whether the opening needs reframing.

Heavy-Duty Sliding Doors

For wider openings, multi-panel sliders, or doors that get daily use from an active household, we install heavy-duty sliders rated for the 140+ mph design wind speed zone Coral Springs falls under. These units use reinforced frames and stainless steel roller assemblies that hold up to decades of wet feet from the lanai and afternoon thunderstorms. In Coral Springs, a heavy-duty two-panel slider typically runs $3,500 to $7,000, and three- or four-panel configurations start around $6,000 and go up from there.

Screen Door Installation

Almost every Coral Springs home with a slider also needs a working screen door for the months when the humidity drops and the lanai becomes livable. We install heavy-duty sliding screen doors that fit the same non-standard track widths as the main door, so you’re not jimmying a big-box screen into a 47-year-old opening. Screen door installation in Coral Springs typically runs $350 to $800 depending on frame material and mesh type.

Pocket & Barn Doors

Some Coral Springs owners are reworking interior layouts and repurposing old slider openings for pocket or barn-style doors. These jobs involve opening walls, and in CBS construction that means cutting block or reframing a load-bearing section. We handle the structural work, the permitting, and the finished door as one scope. Pocket door conversion in a Coral Springs CBS wall typically starts around $2,000, and we’ll tell you before we start whether your wall is load-bearing and what that means for the schedule.

What Happens Behind the Stucco: The Coral Springs Rough Opening Problem

Coral Springs was built almost entirely between the late 1960s and early 1990s by Coral Ridge Properties as one of Florida’s first master-planned cities. That means thousands of CBS homes with the same generation of original aluminum single-pane sliders are now aging out simultaneously, and none of them meet post-Hurricane Andrew Florida Building Code impact requirements. But here’s what matters for your sliding door replacement: the original rough openings were laid out in non-standard block-course increments. A “standard” 72-inch slider almost never drops into a Coral Springs CBS opening without custom sizing or, in many cases, a full reframe.

Ignoring this during quoting is the single most common cause of project cost overruns in Coral Springs. We handle it differently. Our process starts with an on-site inspection where we measure the rough opening in three places, check the lintel and the jambs for rot or termite damage, and determine whether the existing header meets current wind-load requirements under Broward County code. Then we price the job with allowances written into the contract, and any surprise we find gets priced and approved in writing before we touch it. That’s a square deal, in writing, before the first tool comes off the truck.

The Ramblewood Corridor Job

We replaced a corroded 12-foot aluminum slider in a 1980s CBS home off the Ramblewood corridor. The original rough opening was out of square by three-quarters of an inch and the jamb had termite damage behind the stucco. We reframed the pocket to accept a fusion-welded impact-rated unit with low-E glass and argon fill, then flashed the entire perimeter with new flashing tape before reinstalling the stucco to Broward County code. That’s the kind of work these homes regularly require, and it’s exactly the kind of thing a phone quote from a less experienced shop will miss. We plan for it because we’ve done it hundreds of times.

Trusted Brands We Service in Coral Springs

We’re an authorized installer for Window Installation in Coral Springs with more than a dozen manufacturer lines, and for Coral Springs homeowners we most often quote PGT, CGI, and ES Windows. All three build impact-rated sliders that carry Florida Building Code approvals for Broward County’s wind zone. Because we measure every opening twice and quote manufacturer lines side by side on paper, you see exactly what you’re buying and what each option costs. That’s a square deal, not a sales pitch. Dispatching and scheduling for Coral Springs jobs is coordinated from our South FL office, with local crews serving the city directly.

Common Sliding & Patio Doors Problems We See in Coral Springs Homes

• Corroded bottom tracks. Decades of wet feet from the lanai leave salt and chlorinated pool water sitting in the track, and the aluminum corrodes until the door binds or falls off its rollers. In Coral Springs, we see this on nearly every original slider from the 1970s and 1980s.
• Fogged insulated glass. The original jalousie panes adjacent to the slider lose their weatherstripping over time, letting humid air in. The moisture attacks the slider’s seal, and eventually the glass fogs permanently. Once the seal fails, the unit cannot be repaired; it must be replaced.
• Undersized or rotted wood bucks. Opening up an older Coral Springs slider often reveals wood bucks that have rotted behind the stucco or were never sized for current wind-load requirements. Broward County code requires a reframe before the new impact unit can be installed.
• Non-standard rough openings. The original CBS block-course layouts mean replacement sliders cannot simply be swapped for off-the-shelf sizes. Custom or modified units are the norm in Coral Springs, and overlooking this during quoting is the most common cause of cost overruns here.

Pricing for Sliding & Patio Doors in Coral Springs, FL

We Also Serve Cities Near Coral Springs

Our crews work throughout northern Broward County, including Margate, Coconut Creek, Pompano Beach, and Deerfield Beach. If you’re in one of those areas, you’ll get the same inspection-first approach, the same written allowances, and the same guarantee from our Coral Springs team. Call (863) 264-3649 and a live person will schedule your free estimate.

FAQs - Sliding & Patio Doors in Coral Springs

Get a Free Estimate for Sliding & Patio Doors in Coral Springs

If your Coral Springs slider is fogged, binding, corroded, or simply 40 years old, call (863) 264-3649. We’ll schedule a free on-site estimate, measure your rough opening, and give you a written quote with real line items and zero surprises. Sliding & Patio Doors done right, backed by our Done Right Promise and The Keystone Standard, in writing. A live person answers 24/7.

Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Coral Springs and northern Broward County.